ADOBE CC 2019 AMT EMULATOR DRIVER
ADOBE CC 2019 AMT EMULATOR CODE

Set the jumper on the 'WA' and 'WB' terminals. Remove the jumper from the 'TC' and 'E1' terminals.

ADOBE CC 2019 AMT EMULATOR CODE

Remove the jumper from the 'WA' and 'WB' terminals.ДЄfter 4 seconds, read the code by the number of flashes of the ABS indicator. Jump the leads 'TC' and 'E1' of the DLC1 connector.

It is used to read the self-diagnosis codes of additional devices of the vehicle (Tc E1 overlap in the connector causes the codes to be displayed by the ABS, SRS, TRC OFF and Hight control Read the detailed layout on the website: 'Lambda probe: Check American.'

Vf-feedback voltage is the contact whose voltage is the result of computer analysis of the oxygen sensor and the system. When the ignition is turned on, the fuel pump will start immediately. Or high-resistance fast voltmeter.Д¬onclusion to measure or supply voltage to the fuel pump without starting the engine. You can measure the voltage (and its change in time) on the sensor. Connecting a very low-power indicator light between 'B +' and 'W' duplicates the 'Check Engine' light bulb on the instrument panel. The jumpers are removed in reverse order.Д¬onclusion bulbs Check. Not jammed and the E1-Te1 contacts are connected at idle and codes are read. After that, the car should drive about 15 km.

ADOBE CC 2019 AMT EMULATOR DRIVER

13 - Crankshaft Position Sensor (P0335, P1335)ДЎ4 - Ignition system, coil number 1 (P1300) and number 4 (P1315)ДЎ5 - Ignition system, coil в„–2 (P1305) and в„–3 (P1310)ДЎ6 - Automatic Transmission Control SystemДЎ9 - Accelerator pedal position sensor (P1120)ДЎ9 - Accelerator pedal position sensor (P1121)Дў4 - Intake air temperature sensor (P0110)ДЈ1 - Absolute pressure sensor (P0105, P0106)Д¤1 - Throttle Position Sensor (P0120, P0121)Д¤9 - Fuel Pressure Sensor (D-4) (P0190, P0191)ДҐ8 - Drive SCV (D-4) (P1415, P1416, P1653)ДЁ9 - ETCS Drive (P1125, P1126, P1127, P1128, P1129, P1633)Д©8 - Vacuum sensor in the vacuum brake booster (C1200)ДЎ2 - Valve e / m valve (short circuit in the circuit)ДЎ4 - Electric pump relay (short circuit in the circuit)Дў1 - E / m valve front right wheel (open circuit or short circuit)Дў2 - O / m valve of the front left wheel (open circuit or short circuit)Дў3 - E / m valve of the rear right wheel (open circuit or short circuit)Дў4 - E / m valve of the left rear wheel (open circuit or short circuit)ДЈ1 - Front right wheel speed sensor (fault)ДЈ2 - Front left wheel speed sensor (malfunction)ДЈ3 - Rear right wheel speed sensor (malfunction)ДЈ4 - Rear left wheel speed sensor (malfunction)Д¤4 - Deceleration sensor (open circuit or short circuit in the circuit)ДҐ1 - Electric power supply circuit (open circuit or short circuit in the circuit)Д§1 - Front right wheel speed sensor (low signal)Д§2 - Front left wheel speed sensor (low signal)Д§3 - Rear right wheel speed sensor (low signal)Д§4 - Rear left wheel speed sensor (low signal)Д§5 - Front right wheel speed sensor (wrong signal change)Д§6 - Front left wheel speed sensor (incorrect signal change)Д§7 - Rear right wheel speed sensor (incorrect signal change)Д§8 - Rear left wheel speed sensor (wrong signal change)ДЎ1 - Driver's igniter PB (short to ground)ДЎ2 - Driver's igniter PB (short to power)ДЎ3 - Driver's igniter PB (circuit closure)ДЎ5 - Front right SRS sensor (short or open circuit)ДЎ5 - SRS front right sensor (short to ground or power)ДЎ6 - Front-left sensor SRS (short circuit or open circuit)ДЎ6 - Front Left SRS Sensor (short to ground or power)ДҐ1 - Passenger PB igniter (short to ground)ДҐ2 - Passenger PB igniter (short to power)ДҐ3 - Passenger PB igniter (short circuit in the circuit)Д¦1 - Driver Belt Pretensioner Igniter (short to ground)Д¦2 - Driver belt pretensioner igniter (short to power)Д¦3 - Driver Belt Pretensioner Igniter (Short Circuit)Д¦4 - Driver Belt Tensioner Igniter (open circuit)Д§1 - Passenger Pretensioner Igniter (short to ground)Д§2 - Passenger belt pretensioner igniter (short to power)Д§3 - Passenger belt pretensioner igniter (short circuit)Д§4 - Passenger belt pretensioner igniter (open circuit)ДЄccumulation of codes in this mode occurs when the contacts 'E1' and 'Te2' are closed before switching on the ignition.

Adobe cc 2019 amt emulator